Can I Install A Bath Tub Myself?
Can I Install A Bath Tub Myself?
Blog Article
The article below about How to Install a Bathtub Yourself is extremely insightful. Read it yourself and see what you think of it.
Mounting a tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old bathtub is easily accessible, the job can move easily; if you need to open a wall surface to eliminate the old bathtub as well as position the brand-new tub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and embeded in the new one. Make certain you have certified yourself for the task and fit attempting it. As opposed to hiring a specialist to take over a halfway-completed job, it is better to think about using one before you start. Chances are you might need an expert plumber to make tube connections.
This post will certainly assist you mount a new tub in your shower room if you have already acquired a new bathtub and also don't require to change the plan of your previous water pipes.
Your devices and also material list should make up the following:
Getting ready for the Installment
Firstly, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps unit to stop stress on the tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you utilize all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is separate the water. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly troublesome due to the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipelines. As soon as the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Making use of both wooden boards under its feet, position the tub in the required placement. The wooden boards are useful in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub up until the spirit level reads degree.
To install faucets, fit the bottom of the outermost versatile tap port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill the bath tub and additionally check the overflow outlet and also the normal electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the producer's user's manual. Tiling and securing around the bath tub ought to wait up until the bath tub has been utilized at the very least once as this will certainly resolve it into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and the sink. Secure the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous type must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall between the bath as well as the tiling, bring about complications with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and also are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can split rather very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently offered on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very fascinated by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you enjoyed the new entry. If you enjoyed our page kindly don't forget to share it. Thank-you for going through it.
Call Today
Report this page